How to Replace a Kia Sportage Replacement Key
The key of many Kia models has the keyless entry feature built in. The key can be compared to an electronic remote and can be exchanged with a fresh one from an Kia dealer or a locksmith.
Key fobs might stop working for several reasons, including batteries that are dead worn buttons signal interference, water damage and a faulty receiver module. Here are some tips to help you get your Kia key fob that is a replacement for the sportage again.
How to replace a smartkey or remote key?
The battery in your Kia's intelligent key will eventually need to be replaced, whether it's a remote key as well as a push-to start key or a normal metal key that is not equipped with transponder. This is particularly relevant if your vehicle shows a message that states the smart or remote keys have low battery power.
Luckily, this is quite simple to do. In order to replace the key fob battery take out the mechanical key from the slit in the back of the key fob. Then lift the cover. replacing kia key fob The Keylab will be found inside the key fob, which holds the battery in the correct position. Remove the old battery by unwinding the screw using the help of a small screwdriver. Then insert the new one and close the slit inside the key fob.
When the key fob is equipped with an updated battery Test it by pressing the lock and unlock buttons. If the doors lock and unlock exactly as you expect, then you're all set! You can now make use of the Kia's hands-free lock/unlock feature whenever your fingers feel cold or you need to go on errands around Brandon.
Note: Some key fobs (transponder chip or smart keys) may need to have their programming completed. This requires a specific programming machine that only the dealer or automotive locksmith has access to. Other keys (non-transponder metal keys) don't require programming. If you need to reprogramme your key, you'll need to record the key code number on the key code tag.
How do you replace a battery?
If the Kia key fob does not respond when you press the lock/unlock button, it's a sign that the battery is insufficient. A low battery may also cause other issues such as the check engine light coming on or delayed cranking of the engine. Fortunately, replacing the battery on the key fob is a relatively simple DIY task that requires only the most basic tools.
Before beginning the process, make sure that your vehicle is turned off and all doors are shut. Find the small, metal or plastic piece at the bottom of the key fob. Jiggle it until the metal key falls out. Then, you can insert the key in the handle of the door for the driver to unlock your car.
To replace the battery in the key fob, take off the cover on the rear. Use a plastic pry tool to loosen up the latch that holds the black negative cable. Take the old battery out, and then position the new battery so that its "+" side is facing you and the "-" negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position, avoiding excessive force to avoid damaging or breaking the contacts on the metal.
Once the new battery has been installed then turn the key fob off and back on in the ignition repeatedly until the door locks. You can then test your Kia's key fob once more to ensure it's working properly.
How do you replace a keyless key
You can have a standard keyfob or a Smart Key based on the model of Kia Sportage. The smart key comes with an embedded mechanical key blade, unlike the standard key fob, which does not. Both key fobs contain a battery that will eventually require changing. It's an easy task that takes only two minutes.
Be sure to switch off your Kia and be on a flat well-lit and well-lit area before you begin. Keep in mind that the fob contains small pieces that could fall if you're not careful.
The release button for the small size is located on the lower backside. It could be an oval silver button or a rectangular slot. When you press it the mechanical key blade will appear and you will be able to open the key fob.
After the key fob has been opened, remove the battery. The new battery is a CR-2032, and can be purchased online or in your local auto parts shop. When you're done, the key fob will allow you to lock the vehicle, unlock it, and then start your vehicle even if it's not running.
How do you replace the mechanical key
The Kia key fob is an amazing option that lets us lock and unlock our car at the push of a button. But, as with all devices it may have issues occasionally. There are solutions to fix these problems and keep your key fobs working for the duration of.
One of the most frequent problems is a low or dead battery. The fob could be able to stop working entirely or stop working at times. If this is what you are experiencing then replace the battery with an entirely new battery.
If this doesn't solve the issue, try using an ordinary screwdriver with a flat head to push the fob's plastic casing open. Be careful not to damage any internal components, or scratch the plastic. Once open, carefully remove the battery you have been using and replace it with a brand new one.
Close and open the door using the mechanical key. (Every Kia fob comes with a spare mechanical key that fits into the slot). Test the key fob to confirm it's working as intended. Contact a dealer, or a locksmith to fix the issue if the fob is still not working. To avoid lockouts in the future, make sure you get an emergency key that can be able to work with all door and trunk cylinders.